01.05.2019

Mikuni India Increases Productivity Thanks to PCD Tools from MAPAL

Combination tools significantly reduce the machining time for a carburetor housing

When it comes to increasing the level of productivity of existing production processes, Mikuni India Private Limited relies on its preferred tool supplier, MAPAL. This trust has paid off. MAPAL designed a new combination tool for machining carburetor housings. And this tool is a success: With the production time reduced considerably, Mikuni needs one machining centre less for the process.

Toshiya Ochiai and Dinesh Gupta from Mikuni with Rajesh Kumar from MAPAL India are shown on the left.
  • Toshiya Ochiai and Dinesh Gupta from Mikuni with Rajesh Kumar from MAPAL India are shown on the left.
  • A carburettor housing is shown in the image.
  • The teams from Mikunu and MAPAL, a total of eight people, stand in front of the Mikuni India building.
  • A horizontal PCD tool with machine mounting.

Mikuni Corporation was founded in Tokyo in 1923. Today, the Japanese company has a worldwide presence, with branches in the USA, Mexico, Germany, Indonesia, China, Thailand, Taiwan and Korea. In 2008, the company established its Indian subsidiary, Mikuni India Private Limited, in the Indian city of Neemrana, located 122 kilometres south-west of Delhi.

Today, Mikuni India offers its customers a broad range of components for the automotive industry, including carburetors and throttle valves. Mikuni India consequently received the “Best Supplier” award from the automotive industry for its outstanding quality products and terms of delivery.

Challenge: increase the production volume of carburetors

In 2017, Mikuni India faced the challenge of increasing the production volume of carburetors. “Mikuni approached us with the request to considerably accelerate the machining process for large-scale production,” Thanigaraj Sripathy, Managing Director of MAPAL India, remembers.

When carburetor housings are manufactured from an aluminium alloy, the challenging machining of the piston bore and throttle bore are the most time-consuming operations and contribute substantially to the overall cycle time. This was reason enough for the tool specialists at MAPAL to scrutinise these two bores and their machining processes. In the machining process used previously, individual tools with ISO indexable inserts were used for finishing.

A carburettor housing is shown in the image.
MAPAL has optimised the machining of the throttle and piston bores on a carburettor housing such as this one. 

PCD combination tool for the throttle and piston bores

The MAPAL team determined that there was great room for improvement here. “We developed a PCD tool that fine machines both the piston and the throttle bores in a single shot,” explains Sripathy. As PCD tools are produced at the MAPAL subsidiary in India, the new tools could be delivered after a short lead time and used immediately.

MAPAL designed a two-stage PCD combination tool for fine machining the piston bore. Four brazed PCD cutting edges are used for boring (21 mm diameter) and two are used for spot facing (30 mm diameter). The machining is performed with a cutting speed of 250 m/min and a feed rate of 600 mm/min.

A three-stage PCD combination tool with two boring steps (diameters of 24.016 mm and 24.664 mm) with two respectively four cutting edges as well as a stage for spot facing (34 mm diameter) uses the same cutting parameters to manufacture the throttle bore in one shot.

A horizontal PCD tool with machine mounting.
Thanks to multi-stage tools and fine machining in one go, Mikuni does not require an additional machining centre. 

Save a huge amount of time in the overall process

Krishan Gopal, Production Manager at Mikuni India, is impressed: “The tool solution from MAPAL not only reduces the machining time significantly. We also don’t need to use a further machining centre, which frees up capacities. We work with considerably higher cutting speeds and machine the bores in one shot. This allows us to save a huge amount of time in the overall process, which is excellent.”

The set target was reached, and productivity was increased considerably. The company now manufactures 2,400 housings per day. Following this successful process optimisation, the Mikuni management distinguished the project as the best kaizen improvement project of the year. The whole team at Mikuni India is very satisfied with the results achieved using the solutions from MAPAL. And so, parts of this type are to be machined with MAPAL tools in the future, too.

The teams from Mikunu and MAPAL, a total of eight people, stand in front of the Mikuni India building.
The teams from Mikunu and MAPAL India work closely together. 

Kathrin Rehor, PR Project Manager at MAPAL

Contact

Kathrin Rehor Public Relations Kathrin.Rehor@mapal.com Phone: +49 7361 585 3342


Further articles from the section CaseStudies